TP-LINK CPE510 SETUP

TP-Link CPE510 is equipped with dual polarised directional MU MIMO antennas. The TP Link CPE510 is primarily developed for point-to-point and point-to-multipoint long distance transmission. With the PharOS MAXtream TDMA technology, the CPE510 is providing high throughput, improved latency, perfect for long range transmission. The TP-Link CPE510 setup is conducted in numerous methods. You can set it up in many operational modes such as an access point, bridge, client, repeater, AP router, and AP client router. This article shows how to construct a network using TP-Link CPE510 and complete the TP-Link CPE510 repeater setup.

New Extender Setup

TP Link CPE510 Setup as access point

For the TP Link CPE510 setup as access point then, follow the instructions carefully as shown below:

  • When logged into the PharOS dashboard, select the Quick Setup option. 
  • The next step is to select the Access Point option.
  • Subnet mask and IP address for your CPE510 are found in the LAN Settings section of the router.
  • To customise the Wireless settings, navigate to the How to Update TP Link CPE220 extender firmware? Wireless AP Settings and change the SSID name, security mode and encryption key, and other options under the Wireless tab.
  • TP-Link CPE networks require a password key.
  • Once you’re satisfied with everything, click Apply to save your wireless configuration. 
  • The TP-Link cpe510 setup is complete when you click Finish.

TP-LinK CPE510 Repeater Setup

  • Select Repeater as the mode of operation from the Quick Setup again.
  • Then enter the TP-Link device’s LAN IP address and Subnet mask and then click next.
  • Select the Wireless Client settings, and then  click on Survey.
  • As soon as your CPE device detects an upstream network, it will connect to it.
  • In the Wireless Client settings, set up the necessary wireless parameters.
  • Choose WPA-PSK/WPA2-PSK as your security of choice. PSK and Security passwords should match exactly.
  • To complete the TP-Link cpe510 repeater Setup,  click the Finish button.

How to setup TP Link CPE510 extender as client device

  • Select AP Router from the Operation mode drop-down menu on the Quick Setup page.
  • Under the WAN Connection section, select your connection type.
  • Confirm the connection type with your ISP if you are unsure.
  • After that, go to Wireless AP Settings and set the basic wireless parameters.
  • Create a new network, select a security key (WPA-PSK/WPA2-PSk), and input the password.
  • Finally, go over all of the settings and save them.

 

For more information and troubleshooting:

Bridge Mode On The TP Link CPE510 Extender

  • To begin, go to the Quick Setup page and pick Bridge as your operation mode.
  • Then, in the LAN settings, set the LAN IP address and Subnet mask for your CPE510.
  • To scan for the upstream network, click Survey once more under the Wireless Client options.
  • Click the Connect tab after you’ve chosen your preferred network name.
  • Configure the wireless settings, including security mode and the passkey.
  • After that, build a new network for downstream customers by entering the specifications in the AP Settings section.
  • By pressing the Save button, you can now save all of your configurations. Finish your work.

HOW TO SET UP  TP Link CPE510 AS AN AP ROUTER

  • Select AP Router from the Operation mode drop-down menu on the Quick Setup page.
  • Under the WAN Connection section, select your connection type.
  • Confirm the connection type with your ISP if you are unsure.
  • After that, go to Wireless AP Settings and set the basic wireless parameters.
  • Create a new network, select a security key (WPA-PSK/WPA2-PSk), and input the password.
  • Finally, go over all of the settings and save them.

TP Link CPE510 extender as AP Client router

  • To begin, set the operation mode to AP client router.
  • Select your WAN connection type, such as PPPoE, dynamic IP, or static IP, under WAN Connection.
  • Then, in the Wireless Client settings, select the Survey option to scan for the upstream network.
  • Select your network name and then click Connect.
  • In the same area, configure your wireless settings.
  • Create a new network for the downstream clients in the Wireless AP area after that.
  • Click the Apply and then Finish tabs after reading the configurations.
RESETTING THE TP-LINK CPE510 DEVICE

You can conduct a factory reset on the CPE510 if you’re having troubles with it and can’t cure them using simple recommendations. If you forget the admin and Wi-Fi passwords for your TP-Link CPE device, you’ll need to reset it. Here are some simple instructions for resetting your TP-Link CPE extender.

  • The first step is to turn on the CPE device by plugging it into a power outlet.
  • Now, on the TP-Link cpe device, seek for the reset button.
  • It should be inserted into a tiny pinhole on the device’s back or bottom panel.
  • After that, use a paperclip or a pointed pin to hit the reset button.
  • Hold the button down until the CPE device’s System LED glows green.
  • After you’ve finished, press and hold the button for a few seconds before releasing it.
  • All configurations are returned to their default settings after a factory reset.
  • You must also repeat the TP Link cpe510 setup procedure.



TP Link CPE510 Extender Firmware Update

Have you been having issues with your extender’s performance or is it acting strangely? If this is the case, you must update your firmware to the most recent version offered by TP Link CPE510. You will receive the latest features and security updates after doing the TP Link  firmware operation on your booster, which will help you improve the performance of your TP Link CPE510 as well as cure bugs.

  • Make sure your WIFI device is connected to the extender network before attempting to log into the TP Link CPE510 Setup page.
  • Open any web browser and type tplinkrepeater.net into the address box.
  • The user will be forwarded to the login page for the TP Link CPE520 extender.
  • Sign in to your account using your usual login information.
  • Select the “Firmware Upgrade” option from the settings menu.
  • Now press and hold the check button for 5-10 seconds.
  • The new version of your booster will then be displayed.
  • Select “YES” and wait for the version to be upgraded.

CONCLUSION

The TP-Link CPE510 device has been set up and configured in this post. You also learned how to configure your tp link CPE in various modes of operation. If you have any further questions, please don’t hesitate to contact our support team. To speak with one of our technical support representatives, please call  on our toll-free number or start a chat with us.